SERVICE PROCEDURES

2027 FLOAT X2 LIVE VALVE NEO Rebuild

Required Parts

  • 025-03-063 Oil: Suspension Fluid, 4 WT, 1.0 Liter Bottle
  • 803-04-365 Seal Kit: 2026 FLOAT X2 Air Spring and Damper Rebuild

Required Tools

  • 8mm Fork Damper Shaft
  • 398-01-190 Tooling: Firm Mode Piston, 2026 FLOAT X2 & DHX2
  • 398-01-191 Tooling: Bearing Housing Torque, 2026 FLOAT X2
  • 398-01-252 Tooling: Bullet, Damper Body, 2026 FLOAT X2
  • 398-01-253 Tooling: Bullet, Shaft, .500 in (12.7mm), 2026 FLOAT X2 & DHX2
  • 398-01-287 Tooling: VVC Nut Torque Setting Tool, 2026 FLOAT X2 & DHX2
  • 803-00-566 Kit:Bike IFP Depth Setting Tool Set
  • 803-04-354 Kit: Tooling: Clamps, 2026 FLOAT X2/DHX2, Inner Air Sleeve
  • 803-04-355 Kit: Tooling: Clamp, 2026 FLOAT X2/DHX2, Damper Body
  • 803-04-356 Kit: Tooling: 2026, Float X2/DHX2, Base Piston Band Sizer
  • 803-04-357 Tooling: Rear Shock, Air Fill Adaptor, IFP, 2026

Supplies Needed

  • 15mm Socket
  • 16mm Socket
  • 20mm Hex Socket
  • 30mm crows foot
  • 8mm 12 Point Deep Socket
  • Plastic Seal Pick
  • Qty.2 of .0031" THICK VALVES (EXAMPLE 044-03-080).
  • Ratchet
  • Smooth-Jaw Parallel Pliers (knipex)
  • T10 Torx Key
  • T10 Torx Socket
  • T8 Torx Key
  • T8 Torx Socket
  • Tohnichi Torque Screwdriver RTD15CN with 2-15 cNm range
  • Torque Wrench
  • Waste Oil Basin

Warning: Always wear safety glasses and protective gloves during service to prevent potential injury. Failure to wear protective equipment during service may lead to SERIOUS INJURY OR DEATH.

FOX products should be serviced by a trained bicycle service technician, in accordance with FOX specifications. If you have any doubt whether or not you can properly service your FOX product, then DO NOT attempt it. Improperly serviced products can fail, causing the rider to lose control resulting in SERIOUS INJURY OR DEATH.

FOX suspension products contain pressurized nitrogen, air, oil, or all 3. Suspension misuse can cause property damage, SERIOUS INJURY OR DEATH. DO NOT puncture, incinerate or crush any portion of a FOX suspension product. DO NOT attempt to disassemble any portion of a FOX suspension product, unless expressly instructed to do so by the applicable FOX technical documentation, and then ONLY while strictly adhering to all FOX instructions and warnings in that instance.

Modification, improper service, or use of aftermarket replacement parts with FOX forks and shocks may cause the product to malfunction, resulting in SERIOUS INJURY OR DEATH. DO NOT modify any part of a fork or shock, including the fork brace (lower leg cross brace), crown, steerer, upper and lower leg tubes, or internal parts, except as instructed herein. Any unauthorized modification may void the warranty, and may cause failure or the fork or shock, resulting in SERIOUS INJURY OR DEATH

Disassembly

img/help/page3159-825H/IMG_0323 copy-m.jpg

Step 1

Need to note location and orientation of rebound knobs/shaft end eyelet as well as air valve.  Confirm orientation of the two decals with dots are aligned before any disassembly.

img/help/page3159-825H/IMG_0323 copy.jpg
img/help/page3159-825H/IMG_1358 copy-m.jpg

Step 2

Remove the black air cap and thread on your FOX shock pump. Slowly release all air from the main air chamber with your pump making sure the shock does not compress beyond the transfer port to avoid it being stuck down, then remove the pump. Verify that all air has been released by depressing the Schrader valve.

img/help/page3159-825H/IMG_1358 copy.jpg
img/help/page3159-825H/IMG_1359 copy.jpg
img/help/page3159-825H/IMG_1360 copy.jpg
img/help/page3159-825H/IMG_1361 copy.jpg
img/help/page3159-825H/IMG_1362 copy.jpg

 Please verify that all air has been released from the air chamber by pushing down on the Schrader valve core. Failure to release all air pressure before further disassembly may cause parts to eject causing SEVERE INJURY OR DEATH.

img/help/page3159-825H/IMG_1364 copy-m.jpg

Step 3

Push XV sleeve down away from retaining ring. Rotate the wire retaining ring to align the opening in the ring with the tab on eyelet. Use a pick to remove the ring.

img/help/page3159-825H/IMG_1364 copy.jpg
img/help/page3159-825H/IMG_1365 copy.jpg
img/help/page3159-825H/IMG_1366 copy.jpg
img/help/page3159-825H/IMG_1367 copy.jpg
img/help/page3159-825H/IMG_1369 copy-m.jpg

Step 4

Notice: Remove the rebound knob or apply a strip of tape over it to prevent the inside of the XV sleeve from getting scratched, which can cause air leaks.

Slide the outer air sleeve away from the negative air sealhead to remove. 

img/help/page3159-825H/IMG_1369 copy.jpg
img/help/page3159-825H/IMG_1370 copy.jpg
img/help/page3159-825H/IMG_0482 copy.jpg
img/help/page3159-825H/IMG_0484 copy.jpg
img/help/page3159-825H/IMG_1371 copy.jpg
img/help/page3159-825H/IMG_0785 copy-m.jpg

Step 5

Use the X2 air sleeve clamps (PN: 803-04-354) to hold the inner air sleeve while you remove the negative air sealhead with the sealhead tool (PN: 398-00-419) and then the shaft eyelet with Knipex pliers or the eyelet torque tool (PN: 398-00-280).

img/help/page3159-825H/IMG_0785 copy.jpg
img/help/page3159-825H/IMG_1374 copy.jpg
img/help/page3159-825H/IMG_1375 copy.jpg
img/help/page3159-825H/IMG_0793.2 copy.jpg
img/help/page3159-825H/IMG_1379 copy.jpg
img/help/page3159-825H/IMG_1380 copy-m.jpg

Step 6

Unthread the Rezi Fill Air Cap counter-clockwise with a Schrader Valve Stem tool then set aside. Release the IFP pressure by depressing the valve stem inside the Reservoir End Cap.

img/help/page3159-825H/IMG_1380 copy.jpg
img/help/page3159-825H/IMG_1381 copy.jpg
img/help/page3159-825H/IMG_1382 copy.jpg
img/help/page3159-825H/IMG_1383 copy.jpg
img/help/page3159-825H/IMG_1384 copy-m.jpg

Step 7

Push the Reservoir End Cap into the Reservoir to gain access to the wire retaining ring. Remove the wire retaining ring with a thin shim then set aside. Use a small hex wrench to lift the Reservoir End Cap out from the Reservoir.

img/help/page3159-825H/IMG_1384 copy.jpg
img/help/page3159-825H/IMG_1385 copy.jpg
img/help/page3159-825H/IMG_1386 copy.jpg
img/help/page3159-825H/IMG_1387 copy.jpg
img/help/page3159-825H/IMG_1389 copy-m.jpg

Step 8

Unthread the Bleed Screw counter-clockwise with a T8 Torx. Drain the damper oil out over a waste oil basin by cycling the shock with the bleed port facing down into the waste oil basin. You can use the Shaft Eyelet to help you cycle the shock if needed.

img/help/page3159-825H/IMG_1389 copy.jpg
img/help/page3159-825H/IMG_1390 copy.jpg
img/help/page3159-825H/IMG_1391 copy.jpg
img/help/page3159-825H/IMG_1392 copy.jpg
img/help/page3159-825H/IMG_1395 copy-m.jpg

Step 9

Clamp the Body Eyelet in your soft-jawed vise then remove the Bearing Housing Cap and any Travel Spacers (if present) by unthreading counter-clockwise and removing the two screws with a 2mm hex wrench. 

img/help/page3159-825H/IMG_1395 copy.jpg
img/help/page3159-825H/IMG_1396 copy.jpg
img/help/page3159-825H/IMG_1397 copy.jpg
img/help/page3159-825H/IMG_1398 copy.jpg
img/help/page3159-825H/IMG_1402 copy-1-m.jpg

Step 10

Use the Bearing Housing Driver (PN: 398-01-191) to unthread the Bearing Housing Counter-Clockwise. Lift the Shaft Assembly out of the Body then remove the Sleeve Assembly. Pour any oil out from shock body.

img/help/page3159-825H/IMG_1402 copy-1.jpg
img/help/page3159-825H/IMG_1405 copy.jpg
img/help/page3159-825H/IMG_1406 copy.jpg
img/help/page3159-825H/IMG_1407 copy.jpg
img/help/page3159-825H/IMG_1408 copy.jpg
img/help/page3159-825H/IMG_1411 copy-m.jpg

Step 11

Hold the flats of the IFP with needle-nosed pliers while you unthread the IFP bleed screw counter-clockwise with a T15 Torx driver. Remove the bleed screw then remove the IFP by pulling up with needle-nosed pliers.

img/help/page3159-825H/IMG_1411 copy.jpg
img/help/page3159-825H/IMG_1412 copy.jpg
img/help/page3159-825H/IMG_1413 copy.jpg
img/help/page3159-825H/IMG_1415 copy.jpg
img/help/page3159-825H/IMG_1418 copy-m.jpg

Step 12

Remove dowel and LSC clocking plate and set aside.

img/help/page3159-825H/IMG_1418 copy.jpg
img/help/page3159-825H/IMG_1421 copy.jpg
img/help/page3159-825H/IMG_1422 copy.jpg
img/help/page3159-825H/IMG_1423 copy.jpg
img/help/page3159-825H/IMG_1424 copy.jpg
img/help/page3159-825H/IMG_1425 copy.jpg
img/help/page3159-825H/IMG_1427 copy-m.jpg

Step 13

Unthread the Firm Mode adjust set screw by turning it counter-clockwise with a T10 torx. Remove the Firm Mode adjust knob while being careful not to lose the detent balls and springs.

img/help/page3159-825H/IMG_1427 copy.jpg
img/help/page3159-825H/IMG_1428 copy.jpg
img/help/page3159-825H/IMG_1429 copy.jpg
img/help/page3159-825H/IMG_1431 copy.jpg
img/help/page3159-825H/IMG_1432 copy-m.jpg

Step 14

Unthread LSC endcap by turning it counter-clockwise using custom torque spanner socket (PN:398-00-991)

img/help/page3159-825H/IMG_1432 copy.jpg
img/help/page3159-825H/IMG_1457 copy.jpg
img/help/page3159-825H/IMG_1458 copy-m.jpg

Step 15

Remove LSC endcap , spring and check valve.

img/help/page3159-825H/IMG_1458 copy.jpg
img/help/page3159-825H/IMG_1460 copy.jpg
img/help/page3159-825H/IMG_1461 copy-m.jpg

Step 16

Remove base valve assembly. You can use a base stud from an air shaft to thead into the Piston and remove.

img/help/page3159-825H/IMG_1461 copy.jpg
img/help/page3159-825H/IMG_1463 copy.jpg
img/help/page3159-825H/IMG_1464 copy.jpg
img/help/page3159-825H/IMG_1490 copy-m.jpg

Step 17

Clean the Damper Body and Clamps with Isopropyl alcohol. Clamp the Body in your Damper Body Clamps (PN:803-04-355) then heat the body area of the eyelet to break down the Loctite. Unthread the Body counter-clockwise from the Eyelet. Take care as the eyelet may be hot!

img/help/page3159-825H/IMG_1490 copy.jpg
img/help/page3159-825H/IMG_1494 copy.jpg
img/help/page3159-825H/IMG_1495 copy.jpg
img/help/page3159-825H/IMG_1055 copy-m.jpg

Step 18

Clamp the eyelet assembly then loosen up the HSR Adjust Clamp set screw with a T10 torx. Use a 1.5mm hex key to turn the HSR adjuster shaft clockwise (causing the HSR knob to also turn), which will unthread the HSR Adjust Clamp. Remove HSR clamp, Leaf Springs and VVC Plate.

img/help/page3159-825H/IMG_1055 copy.jpg
img/help/page3159-825H/IMG_1056 copy.jpg
img/help/page3159-825H/IMG_1057 copy.jpg
img/help/page3159-825H/IMG_1059 copy.jpg
img/help/page3159-825H/IMG_1061 copy.jpg
img/help/page3159-825H/IMG_0898.2 copy.jpg
img/help/page3159-825H/IMG_0330 copy-m.jpg

Step 19

Unthread Piston bolt using a 16mm socket.

img/help/page3159-825H/IMG_0330 copy.jpg
img/help/page3159-825H/IMG_9483 - Copy copy.jpg
img/help/page3159-825H/IMG_0002 copy-m.jpg

Step 20

Pull the Rebound Rod out from the Shaft. Remove the Bearing Assembly by pulling it up off of the shaft, followed by Bearing Housing Cap, MCU Bumper and Bottom Out O-ring. 

img/help/page3159-825H/IMG_0002 copy.jpg
img/help/page3159-825H/IMG_0004 copy.jpg
img/help/page3159-825H/IMG_0005 copy.jpg
img/help/page3159-825H/IMG_0006 copy.jpg
img/help/page3159-825H/IMG_0007 copy.jpg
img/help/page3159-825H/IMG_0008 copy-m.jpg

Step 21

Clean the exposed shaft and clamps with Isopropyl alcohol then dry it with a lint-free paper towel. Invert the shock, then carefully clamp the shaft in your clamps (PN: 803-00-805).  Heat the shaft/eyelet junction with a torch to loosen the Loctite. Unthread the eyelet counter-clockwise to remove. 

img/help/page3159-825H/IMG_0008 copy.jpg
img/help/page3159-825H/IMG_0805 copy.jpg
img/help/page3159-825H/IMG_0806.2 copy 2.jpg
img/help/page3159-825H/IMG_0375 copy-m.jpg

Step 22

Remove Compression Valving, Main Piston, and Rebound Valving from Piston Bolt

img/help/page3159-825H/IMG_0375 copy.jpg
img/help/page3159-825H/IMG_0359 copy-m.jpg

Step 23

Note: The next two steps only need to be performed if changing the bleed shim.

Use a T25 to hold the HSR Adjuster Shaft to unthread the HSR Adjuster Nut counterclockwise using a 8mm 12point deep socket.

 

img/help/page3159-825H/IMG_0359 copy.jpg
img/help/page3159-825H/IMG_0361 copy.jpg
img/help/page3159-825H/IMG_0373 copy-m.jpg

Step 24

Remove HSR adjuster nut, spring washer, valve and bleed shim.

img/help/page3159-825H/IMG_0373 copy.jpg
img/help/page3159-825H/IMG_0369 copy.jpg
img/help/page3159-825H/IMG_0368 copy.jpg
img/help/page3159-825H/IMG_0367 copy.jpg

Reassembly

img/help/page3159-825H/IMG_0980 - Copy copy-m.jpg

Step 1

Use a plastic pick to replace the all seals on the Bearing Assembly,  with new greased ones from the kit. Verify that the o-rings within the Bearing Assembly have been seated properly. Also replace the Topout Bumper and Back up rings.

img/help/page3159-825H/IMG_0980 - Copy copy.jpg
img/help/page3159-825H/IMG_0982 copy.jpg
img/help/page3159-825H/IMG_0981 - Copy copy.jpg
img/help/page3159-825H/IMG_0966 copy-m.jpg

Step 2

Use a plastic pick to replace the seals and back up rings on the Neg Air Sealhead with new greased ones from the kit.

img/help/page3159-825H/IMG_0966 copy.jpg
img/help/page3159-825H/IMG_0967 copy.jpg
img/help/page3159-825H/IMG_0968 copy-m.jpg

Step 3

Use a plastic pick to replace IFP o-ring with a new greased one from the kit. Replace the o-rings on the Reservoir End Cap, Air Fill Cap and Bleed screw with new greased ones from the kit.

img/help/page3159-825H/IMG_0968 copy.jpg
img/help/page3159-825H/IMG_0969 copy.jpg
img/help/page3159-825H/IMG_0975 - Copy copy.jpg
img/help/page3159-825H/IMG_0974 - Copy copy.jpg
img/help/page3159-825H/IMG_9990 copy-m.jpg

Step 4

Clean shaft threads and apply Loctite activator 7649 and red Loctite 277 to 2-3 threads of the Outer Shaft making sure not to get Loctite on the Inner Shaft.

img/help/page3159-825H/IMG_9990 copy.jpg
img/help/page3159-825H/IMG_9991 copy-m.jpg

Step 5

Carefully thread on the eyelet to shaft observing any binding.  If there is any binding, turning the HSR knob slightly might be necessary to avoid damaging the gear parts.  When the shaft and eyelet are snug turn the HSR knob by hand to ensure it turns freely before torquing the eyelet. Clean the shaft with Isopropyl alcohol and a lint-free paper towel then clamp in your 1/2" shaft clamps. Tighten the Shaft Eyelet clockwise to 245 in-lb (27.68 Nm) torque with your Eyelet Torque Tool.

img/help/page3159-825H/IMG_9991 copy.jpg
img/help/page3159-825H/IMG_9992 copy.jpg
img/help/page3159-825H/IMG_9993 copy.jpg
img/help/page3159-825H/IMG_9994 copy.jpg
img/help/page3159-825H/IMG_0926 copy.jpg
img/help/page3159-825H/IMG_0007.2 copy-m.jpg

Step 6

Install a new bottom out bumpers and Bearing Housing Cap (Important: Note orientation of countersink holes). Coat the seals of the Bearing Assembly with a thin film of Slick Honey, then reinstall the Bearing Assembly onto the shaft using 1/2" Shaft Bullet (PN:398-01-253) as shown. Reinstall Rebound Rod into shaft after replacing O-ring with new greased one from the kit.

img/help/page3159-825H/IMG_0007.2 copy.jpg
img/help/page3159-825H/IMG_9474 - Copy copy.jpg
img/help/page3159-825H/IMG_9477 - Copy copy.jpg
img/help/page3159-825H/IMG_0910 copy.jpg
img/help/page3159-825H/IMG_9478 - Copy copy.jpg
img/help/page3159-825H/IMG_9479 - Copy copy.jpg
img/help/page3159-825H/IMG_0001 copy.jpg
img/help/page3159-825H/IMG_0002.2 copy.jpg
img/help/page3159-825H/IMG_0334 copy-m.jpg

Step 7

Ensure Rebound Rod is fully seated in the Cam Slot by turning HSR knob to make sure the rod turns and turning the LSR knob counter-clockwise while pushing in on the rebound rod and the knob stops.

img/help/page3159-825H/IMG_0334 copy.jpg
img/help/page3159-825H/IMG_0335 copy.jpg
img/help/page3159-825H/IMG_0331 copy.jpg
img/help/page3159-825H/IMG_0333 copy-2.jpg
img/help/page3159-825H/IMG_0367.2 copy-m.jpg

Step 8

Reinstall bleed shim, valve, spring washer onto Piston Bolt.

 

img/help/page3159-825H/IMG_0367.2 copy.jpg
img/help/page3159-825H/IMG_0368.2 copy.jpg
img/help/page3159-825H/IMG_0369.2 copy.jpg
img/help/page3159-825H/IMG_0370 copy-m.jpg

Step 9

Install HSR Adjuster Shaft and thread on HSR Adjuster Nut. Torque to 15in-lb (1.7Nm) using a 12point 8mm socket and a T25 to hold the HSR Adjuster Shaft.

img/help/page3159-825H/IMG_0370 copy.jpg
img/help/page3159-825H/IMG_0362 copy.jpg
img/help/page3159-825H/IMG_0374 copy.jpg
img/help/page3159-825H/IMG_0916 copy-m.jpg

Step 10

Thread on Piston Bolt and torque with 16mm hex to 80in-lbs(9.0Nm) without the VVC Plate in place.

img/help/page3159-825H/IMG_0916 copy.jpg
img/help/page3159-825H/IMG_9972 copy.jpg
img/help/page3159-825H/IMG_1064 copy-m.jpg

Step 11

  1. install VVC Plate
  2. Run down HSR clamp and leaf springs using a 1.5mm hex.
  3. Obtain qty 2 .0031" thick valves (example 044-03-080).
  4. Locate holes on VVC plate in middle of VVC range.
  5. Place 1 valve on either side between VVC plate and .900 valve and aligned with holes from step 4
  6. Adjust HSR adjuster shaft so the VVC adjuster nut turns freely and and there is no preload on the leaf valves.
  7. Adjust the HSR knob clockwise 1 click at a time until the leaf springs are aligned to the holes in step 4 when torqued to the specification on the leaf valve stack. Note: Each VVC leaf valving assembly has its own torque specification.
  8. Torque m3 fastener in HSR adjust clamp to 15in/lbs.
  9. Remove .0031" shims

Note: HSR VVC Leaf Valves orientation is critical and can be found here»

Note: Turn HSR knob and ensure the VVC clamp nut rotates freely through the range of travel in the VVC plate

 

img/help/page3159-825H/IMG_1064 copy.jpg
img/help/page3159-825H/IMG_9486 copy.jpg
img/help/page3159-825H/IMG_9488.2 copy.jpg
img/help/page3159-825H/IMG_9485.2 copy.jpg
img/help/page3159-825H/IMG_1066 copy.jpg
img/help/page3159-825H/IMG_9491 copy.jpg
img/help/page3159-825H/IMG_9981 copy.jpg
img/help/page3159-825H/IMG_9982 copy.jpg
img/help/page3159-825H/IMG_9984 copy.jpg
img/help/page3159-825H/IMG_1497 copy-m.jpg

Step 12

Replace the eyelet o-ring with one greased one from the kit. Clean threads of body with alcohol. Apply Loctite activator 7649 and red Loctite 277 to 2-3 threads for a full 360 degrees on the body. Reinstall the Body on the eyelet assy tightening clockwise by hand. Clamp the Outer Body in your shaft clamps, then use the Eyelet Torque Tool to tighten clockwise to 35ft-lb (47.5 Nm) torque.

img/help/page3159-825H/IMG_1497 copy.jpg
img/help/page3159-825H/IMG_1499 copy.jpg
img/help/page3159-825H/IMG_1500 copy.jpg
img/help/page3159-825H/IMG_1501 copy.jpg
img/help/page3159-825H/IMG_1524 copy-m.jpg

Step 13

Install a new Sag Indicator O-ring from the kit onto the body.  Coat the seals with a thin film of 20 wt. Gold oil then reinstall the Neg Air Sealhead onto the Body using damper body Bullet (PN:398-01-252) as shown. Reinstall any Negative Air Volume Spacers if present. Reinstall Inner Air Sleeve. 

img/help/page3159-825H/IMG_1524 copy.jpg
img/help/page3159-825H/IMG_1526 copy.jpg
img/help/page3159-825H/IMG_1527 copy.jpg
img/help/page3159-825H/IMG_1529 copy.jpg
img/help/page3159-825H/IMG_1530 copy.jpg
img/help/page3159-825H/IMG_1531 copy-m.jpg

Step 14

Reinstall the rebuild Shaft Assembly into the Body. tighten clockwise torque with the Bearing Housing Driver (PN: 398-01-191) to 30 ft-lb (40.7 Nm).

img/help/page3159-825H/IMG_1531 copy.jpg
img/help/page3159-825H/IMG_1532 copy.jpg
img/help/page3159-825H/IMG_1534 copy.jpg
img/help/page3159-825H/IMG_1597 copy-m.jpg

Step 15

Replace the o-ring on the IFP with a new greased one from the kit. Coat the inside wall of the reservoir with a thin film of FOX 4 wt. oil. Reinstall the IFP into the reservoir. Reinstall the bleed screw with new greased o-ring from the kit into the IFP, tightening clockwise to 7in-lb (0.8 Nm) torque while holding the flats of the IFP. Reinstall the wire retaining ring into the groove in the reservoir as shown.

img/help/page3159-825H/IMG_1597 copy.jpg
img/help/page3159-825H/IMG_1599 copy.jpg
img/help/page3159-825H/IMG_1600 copy.jpg
img/help/page3159-825H/IMG_1709 copy-m.jpg

Step 16

Thread the fill machine adapter clockwise into the bleed port. Apply vacuum to the shock, then fill with FOX 4wt oil while cycling it a few times. Using the IFP depth setting tool (803-00-566), set the IFP depth.

IFP Height Medium Reservoir 37 +/- 1.25mm (1.457 +/- .050in.)
  Long Reservoir 41 +/- 1.25mm (1.614 +/- .050in.)
  XL Reservoir 45 +/- 1.25mm (1.772 +/- 050in.)
IFP Pressure 150psi +/- 10psi  

 

Reinstall the set screw with a new greased o-ring from the kit and tighten to 10 in-lb (1.1 Nm).

img/help/page3159-825H/IMG_1709 copy.jpg
img/help/page3159-825H/IMG_1713 copy.jpg
img/help/page3159-825H/IMG_1714 copy.jpg
img/help/page3159-825H/IMG_1715 copy.jpg
img/help/page3159-825H/IMG_1716 copy.jpg
img/help/page3159-825H/IMG_1601 copy-m.jpg

Step 17

Remove the wire retaining ring from the Reservoir. Coat the o-ring of the Reservoir End Cap with a thin film of Slick Honey then reinstall into the Reservoir. Push the End Cap down then reinstall the wire retaining ring.

img/help/page3159-825H/IMG_1601 copy.jpg
img/help/page3159-825H/IMG_1602 copy.jpg
img/help/page3159-825H/IMG_1603 copy.jpg
img/help/page3159-825H/IMG_1604 copy.jpg
img/help/page3159-825H/IMG_1605 copy.jpg
img/help/page3159-825H/IMG_1721 copy-m.jpg

Step 18

Use a small hex wrench to align Reservoir End Cap ( port pointed towards rebound end of shock for transverse rezi and parallel to shock axis for parallel rezi). Install the Rezi Fill Adaptor (PN:803-04-357) by threading it in clockwise. Set the IFP pressure to 150 psi. Remove the Fill Adaptor and reinstall the Rezi Fill Air Cap with a Schrader Valve tool, tightening clockwise to 3 in-lb (0.3 Nm) torque. 

img/help/page3159-825H/IMG_1721 copy.jpg
img/help/page3159-825H/IMG_1724 copy.jpg
img/help/page3159-825H/IMG_1725 copy.jpg
img/help/page3159-825H/IMG_1728 copy.jpg
img/help/page3159-825H/IMG_1729 copy.jpg
img/help/page3159-825H/IMG_9796 copy-m.jpg

Step 19

Apply 2cc of FOX 20wt. Gold oil onto the Bearing Assembly then reinstall the Inner Air Sleeve as shown. Thread the Shaft Eyelet clockwise onto the Inner Air Sleeve then clamp the Shaft Eyelet in your soft-jawed vise. Tighten the Neg Air Sealhead clockwise to 22ft-lbf (29.8 Nm) torque. 

img/help/page3159-825H/IMG_9796 copy.jpg
img/help/page3159-825H/IMG_9795 copy.jpg
img/help/page3159-825H/IMG_9797 copy.jpg
img/help/page3159-825H/IMG_9798 copy.jpg
img/help/page3159-825H/IMG_9799 copy-m.jpg

Step 20

Reinstall any Positive Volume Spacers. Coat the air seals in a thin film of Slick Honey then reinstall the outer air sleeve with the air valve side first. Remove the rebound knob or apply a strip of tape over it to prevent the inside of the XV sleeve from getting scratched, which can cause air leaks. Slide the outer air sleeve all the way to the negative air sealhead to engage the air seals. Reinstall the wire retaining ring making sure that it is fully seated in its groove.

img/help/page3159-825H/IMG_9799 copy.jpg
img/help/page3159-825H/IMG_0485 copy.jpg
img/help/page3159-825H/IMG_0486 copy.jpg
img/help/page3159-825H/IMG_0488.2 copy.jpg
img/help/page3159-825H/IMG_9801 copy.jpg
img/help/page3159-825H/IMG_9802 copy.jpg
img/help/page3159-825H/IMG_0771 copy-m.jpg

Step 21

Attach your shock pump then add air while you slowly cycle your shock through 25% of its travel 10 times as you reach your desired pressure. Reinstall the black air cap.

img/help/page3159-825H/IMG_0771 copy.jpg
img/help/page3159-825H/IMG_0773.2 copy.jpg
img/help/page3159-825H/IMG_0766.2 copy.jpg

Air Sleeve Installation

Rear shock setup and configuration varies greatly between different bicycle manufacturers. Be sure to refer to the owner’s manual for your bicycle. FOX products should be installed by a qualified bicycle service technician, in accordance with FOX installation specifications. Improperly installed shocks can fail, causing the rider to lose control, resulting in SERIOUS INJURY OR DEATH.

 

Important Note: Air valve can hit the Transverse Rezi if proper alignment is not followed. Pay close attention to Air Valve location. Additionally strut mount bikes need additional attention, as rotating the remound eyelet 90 degrees can put the air valve in an incompatible location.

img/help/page3159-825H/IMG_0323.3 copy-m.jpg

Step 1

The shock has a pair of decals installed that show the factory alignment of the air valve/XV sleeve. When changing volume spacers or performing any shock service, you must ensure the shock is reassembled with the dots aligned. Failure to do so may result in shock or frame damage. If you are re-aligning the air valve/XV sleeve, you must remove the lower decal and affix a replacement (included with aftermarket product) so they are aligned as shown.

img/help/page3159-825H/IMG_0323.3 copy.jpg
img/help/page3159-825H/IMG_0336 copy-m.jpg

Step 2

Remove the air cap, attach a shock pump, then SLOWLY release all air out of the main air chamber.

img/help/page3159-825H/IMG_0336 copy.jpg
img/help/page3159-825H/IMG_0339 copy.jpg
img/help/page3159-825H/IMG_0338 copy.jpg
img/help/page3159-825H/IMG_0341 copy-m.jpg

Step 3

Push XV sleeve down away from retaining ring. Rotate the wire retaining ring to align the opening in the ring with the tab on eyelet. Use a pick to remove the ring.

img/help/page3159-825H/IMG_0341 copy.jpg
img/help/page3159-825H/IMG_0356 copy.jpg
img/help/page3159-825H/IMG_0485.2 copy-m.jpg

Step 4

Note: Remove the rebound knob or apply a strip of tape over it to prevent the inside of the XV sleeve from getting scratched, which can cause air leaks.

Slide the outer air sleeve away from the negative air sealhead. 

img/help/page3159-825H/IMG_0485.2 copy.jpg
img/help/page3159-825H/IMG_0342 copy.jpg
img/help/page3159-825H/IMG_0343 copy.jpg
img/help/page3159-825H/IMG_1731 copy-m.jpg

Step 5

Your shock should come positioned correctly on your bicycle from the factory. However, if the XV air sleeve is rotated for any reason, it must not interfere with any part of the shock or frame. In the examples below, the XV air sleeve/air valve is rotated separately from the rebound eyelet. Images show a few examples of air valve positions to achieve proper clearance between the air valve and shock reservoir, but the shock would still need to be tested for frame clearance throughout the entire stroke.

img/help/page3159-825H/IMG_1731 copy.jpg
img/help/page3159-825H/IMG_1734 copy.jpg
img/help/page3159-825H/IMG_1736 copy.jpg
img/help/page3159-825H/IMG_1735 copy.jpg
img/help/page3159-825H/IMG_0377 copy-m.jpg

Step 6

Install the shock onto your frame according to your frame manufacturer’s instructions. Slowly compress the suspension through its entire travel. Check that the shock does NOT contact any portion of your frame or linkage as it cycles through its travel.

img/help/page3159-825H/IMG_0377 copy.jpg
img/help/page3159-825H/IMG_0380 copy.jpg
img/help/page3159-825H/IMG_0381 copy.jpg
img/help/page3159-825H/IMG_0355 copy-m.jpg

Step 7

Slide the XV sleeve down to the negative air sealhead to engage the air seals. Reinstall the wire retaining ring, and make sure that it is fully seated in its groove. 

img/help/page3159-825H/IMG_0355 copy.jpg
img/help/page3159-825H/IMG_0356.2 copy.jpg
img/help/page3159-825H/IMG_0357 copy.jpg